목적
Simulators mimic the electrical signal from a typical vacuum gauge at various vacuum levels/pressures. Their most common use is troubleshooting vacuum systems and identifying potential setup issues. This application note outlines simulators offered by Televac® and how they can be used.
Simulator Types
Televac® offers simulators for many of our most popular vacuum sensors. These simulators come in two different types:
1. 제로 포인트 시뮬레이터는 0 micons / mTorr에서 일반적인 진공 게이지 출력을 시뮬레이션합니다.
2. 멀티 포인트 시뮬레이터는 여러 압력에서 일반적인 진공 게이지 출력을 시뮬레이션합니다.
사용 가능한 시뮬레이터는 다음과 같습니다.
센서 모델 | 시뮬레이션된 압력 | 부품 번호 |
2A 써모커플 | 0(레드 라인, 0 미크론) 3점(0, 100, 1000 미크론) |
2-2100-237 2-2100-242 |
2A 미니 써모커플 | 0(레드 라인, 0 미크론) 3점(0, 100, 1000 미크론) |
2-2100-240 2-2100-241 |
4A 대류 | 0(레드 라인, 0 미크론) 3점(0, 1, 760 토르) |
2-2119-000 2-2119-003 |
7B 페닝 그자석론 | 2점(10-3,10-5 토르) 4점(10-3,10-4,10-5,10-6 토르) |
2-2100-93 2-2100-108 |
7E 더블 반전 자석 | 2점(10-2,10-5 토르) | 2-2142-000 |
7F 더블 반전 자석 | 2점(10-3,10-5 토르) | 2-2145-000 |
Using Simulators to Troubleshoot
If the vacuum readings on your Televac® controller are incorrect, it can be challenging to determine which part of the setup is causing the issue. Several troubleshooting methods are described below:
1. 시뮬레이터는 일반적인 진공 게이지에서 전기 신호를 나타내기 때문에 진공 게이지가 문제를 일으키는지 여부를 테스트하는 데 사용할 수 있습니다. 이 테스트를 위해 진공 게이지를 시뮬레이터로 바꾸고 컨트롤러의 출력이 합리적인 허용 오차 내에 있는지 확인합니다. 그렇지 않은 경우 게이지를 교체해야 할 수 있습니다.
2. 거의 모든 차가운 음극 게이지를 청소할 수 있으며, 이 게이지에 문제가 해결될 수 있습니다. 자세한 정보와 청소 절차에 대한 응용 프로그램 노트 3002 (7B 및 7E) 및 응용 프로그램 주 3004 (7FC 및 7FCS)를 참조하십시오.
3. 게이지를 교체해도 문제가 해결되지 않으면 시뮬레이터를 사용하여 진공을 당기지 않고 다른 시스템 구성 요소를 테스트할 수도 있습니다. 예를 들어 시뮬레이터와 함께 다른 케이블을 사용하여 문제가 있는 판독값을 수정하는지 확인할 수 있습니다.
A Note on Using Simulators For Calibration
Calibration is a common step in the set up of a vacuum controller. It ensures that the controller readings with a corresponding vacuum gauge are in tolerance. Simulators don’t account for gauge to gauge variation because a simulator is representative of a typical vacuum gauge. Therefore, calibrating with a simulator can cause incorrect readings when a vacuum gauge is connected. Because of this, Televac® does not recommend attempting to calibrate a vacuum controller using a simulator.
For more information on Televac®’s recommended practices for field calibration of vacuum systems, please see Application Note 3015.
관련 제품
• Sensor simulators are designed to electrically simulate Televac sensors at specific pressures. These units allow for simple troubleshooting of issues relating to cabling, sensors, and electronics.